[NTLUG:Discuss] Fedora on Dell PowerEdge 700 does not find NIC
Neil Aggarwal
neil at JAMMConsulting.com
Fri Apr 9 10:54:28 CDT 2004
Justin:
I am attaching the modules.conf here.
lspci -vv Gives me:
00:00.0 Host bridge: Intel Corp. 82875P Memory Controller Hub (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at fe800000 (32-bit, prefetchable) [size=4M]
Capabilities: [e4] #09 [3106]
00:03.0 PCI bridge: Intel Corp. 82875P Processor to PCI to CSA Bridge
(rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe100000-fe2fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1c.0 PCI bridge: Intel Corp.: Unknown device 25ae (rev 02) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 10
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE+ ERO- RBC=0 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
00:1d.0 USB Controller: Intel Corp.: Unknown device 25a9 (rev 02)
(prog-if 00 [UHCI])
Subsystem: Dell Computer Corporation: Unknown device 0167
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at cce0 [size=32]
00:1d.4 System peripheral: Intel Corp.: Unknown device 25ab (rev 02)
Subsystem: Dell Computer Corporation: Unknown device 0167
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at fe300400 (32-bit, non-prefetchable)
[size=16]
00:1d.5 PIC: Intel Corp.: Unknown device 25ac (rev 02) (prog-if 20
[IO(X)-APIC])
Subsystem: Dell Computer Corporation: Unknown device 0167
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
00:1d.7 USB Controller: Intel Corp.: Unknown device 25ad (rev 02)
(prog-if 20 [EHCI])
Subsystem: Dell Computer Corporation: Unknown device 0167
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at fe300000 (32-bit, non-prefetchable)
[size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [2080]
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 0a)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fc000000-fdffffff
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp.: Unknown device 25a1 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.2 IDE interface: Intel Corp.: Unknown device 25a3 (rev 02)
(prog-if 8a [Master SecP PriP])
Subsystem: Dell Computer Corporation: Unknown device 0167
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fea0 [size=16]
00:1f.3 SMBus: Intel Corp.: Unknown device 25a4 (rev 02)
Subsystem: Dell Computer Corporation: Unknown device 0167
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 08c0 [size=32]
01:01.0 Ethernet controller: Intel Corp.: Unknown device 1075
Subsystem: Dell Computer Corporation: Unknown device 0167
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (63750ns min), cache line size 10
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe1e0000 (32-bit, non-prefetchable)
[size=128K]
Region 2: I/O ports at ece0 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
03:0e.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
(prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 0167
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 10
Region 0: Memory at fc000000 (32-bit, non-prefetchable)
[size=16M]
Region 1: I/O ports at dc00 [size=256]
Region 2: Memory at fdeff000 (32-bit, non-prefetchable)
[size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Let me know what to do next.
Thanks,
Neil
--
Neil Aggarwal, JAMM Consulting, (972)612-6056, www.JAMMConsulting.com
FREE! Valuable info on how your business can reduce operating costs by
17% or more in 6 months or less! => http://newsletter.JAMMConsulting.com
> -----Original Message-----
> From: discuss-bounces at ntlug.org
> [mailto:discuss-bounces at ntlug.org] On Behalf Of Justin M. Forbes
> Sent: Friday, April 09, 2004 10:09 AM
> To: NTLUG Discussion List
> Subject: Re: [NTLUG:Discuss] Fedora on Dell PowerEdge 700
> does not find NIC
>
>
> Can you please send me the output of 'lspci -vv' and attach a
> copy of your
> /etc/mudules.conf? This should not be happening, so I will
> see what the
> deal is, it is possible that Dell used a new revision of the
> onboard or
> something which identifies differently, if so, I will send
> you an updated
> hwdata which should fix autodetection for other servers.
>
> Thanks,
> Justin M. Forbes
>
> _______________________________________________
> https://ntlug.org/mailman/listinfo/discuss
>
More information about the Discuss
mailing list